ADC0808 PDF

The ADC IC is a commonly used ADC module for projects were an external ADC is required. Find ADC pin diagram, features & datasheet. ADC – A/D converters, used to convert analog signal to digital signals, like ADC IC, ADC IC, pin configurations and interfacing with microcontroller . The ADC/ADC is an 8 bit ADC that also contains an 8 channel multiplexer. The FPGA used in this case was the Altera 10k20RC that is found on.

Author: Tauhn Shakalar
Country: Uganda
Language: English (Spanish)
Genre: Marketing
Published (Last): 25 October 2010
Pages: 470
PDF File Size: 8.50 Mb
ePub File Size: 19.34 Mb
ISBN: 446-6-17421-428-7
Downloads: 40002
Price: Free* [*Free Regsitration Required]
Uploader: Gardar

This means that in order to get it to work, there is a total of seven control signals that must be sent from the FPGA. It is a pin Eight channel 8-bit ADC module.

Address Lines Because the chip has an 8 channel multiplexer there are three address select lines: Complete Technical Details can be ad0808 at the datasheet give at the end of adc080 page. I have not tested on the actual hardware but i have done the simulation in proteus and it works. Start The purpose of the start signal is two fold. Source code The source code consists of a few of files.

In the above circuit I have used a potentiometer to feed in a variable voltage of 0V to 5V to the IN1 pin and the present Voltage is read using a voltmeter.

ADC Technical Data

See table 1 for details. Be sure to consult the ad0808 data-sheets for other chips. The voltage level that, when received as an input, will output “” to the FPGA. Begin by downloading the files into your desired destination directory and then compile them in this order.

Related Posts  MGMA PHYSICIAN COMPENSATION 2012 PDF

Top menu About Us Advertise. Atmospheric Vortex Engine Twister Power. The ALE should be pulsed for at least ns in add0808 for the addresses to get loaded properly.

IC ADC0808

Log in or register to post Comment. And show on LCD as name Ch2. Up to 72 if the start signal is received in the middle of an 8 clock cycle period.

The signal goes low once a conversion is initiated by the start signal and remains low until a conversion is complete. These 7 pins adc8008 the input adc0088 for Analog voltage sensor.

SPI Module of Arduino. It is a control signal from the FPGA, which tells the converter when to start a conversion. This is a bit of the digital converted output. And data pin D4-D7 is connected to pins P2. Skip to main content.

And the formula for radiometric conversion is given by: This device has three channel address line namely: It is recomended that the source resistance not adc088 5kohms for operation at 1. Unfortunately you cannot just hook up analog inputs to an ADC and expect to get digital outputs from the chip without adding control signals. I have made small changes to the original code. And by using their ADC register we adc088 interface.

Choosing Motor For Robots. Connect to ground of the circuit. Then microcontroller shows its value at Ch1 position in LCD. Has to be made high to get output on output pins. Analog signal has infinite no of values like a sine wave or our speech, ADC converts them adf0808 particular levels or states, which can be measured in numbers as a physical quantity.

Related Posts  OVIDIU DRAGOS ARGESANU PDF

Access Denied

Actually the code u have posted is not working i guess due to the initialization i think. The signal can be tie to the ALE signal when the clock frequency is below kHz.

Top menu About Us Contact. Interface SD Card with Arduino. We can provide it by using oscillator or by using microcontroller. Analog Channel 1 to 5. Input pin; a low to high pulse brings data to output pins from the internal registers at end of conversion. This means it must remain stable for up to 72 clock cycles. This means that an entire conversion takes at least 64 clock cycles.

Table 2 provides a summary of all of the input and output to the chip. Instead of continuous conversion, ADC converts data periodically, which xdc0808 usually known as sampling rate. ADC is the Analog to Digital converterwhich converts analog data into digital format; usually it is used to convert analog voltage into digital format.

Interfacing ADC with Microcontroller: Tutorial with Circuit Diagram and Code

ADC is an 8 bit analog to digital converter with eight input analog channels, i. The maximum frequence of the clock is 1. The source resistance must be below 10kohms adc08088 operation below kHz and below 5kohms for operation around 1. That is because ADCs require clocking and can contain control logic including comparators and registers.

It is the Second bit of the select lines.